Fascia Board Materials Compared: uPVC vs Aluminium vs Composite vs Timber
By Central Scotland Roofline · Published 12/09/2026 · Updated 22/09/2026 · 9 min read
"uPVC or timber" is the comparison most articles stop at, but two more options – aluminium and composite – show up regularly in quotes for Scottish properties, particularly anything coastal, listed, or at the upper end of the market. Getting the choice right matters more in Scotland than in most of the UK: freeze-thaw cycles, sustained wind-driven rain from the Atlantic and salt-laden air on the coast all put fascia materials through cycles that a dry Southern climate does not. Here is how all four compare on cost, lifespan, Scottish weather performance and the standards they are actually built to.
uPVC
The default choice for most homes. Modern uPVC roofline is manufactured to BS 7413, which sets minimum wall thickness (typically 9 mm for a full-replacement board, not the 6 mm "cap-over" boards that some cheap quotes rely on), impact resistance and colourfastness. A quality BS 7413 board will not soften, sag or lose its colour over a normal Scottish lifespan.
Typical 2026 supply-and-fit cost is £25–£40 per linear metre for standard white or woodgrain finishes on a straightforward two-storey property, rising to £45–£60 for anthracite grey and other colour finishes.
- Lifespan: 25–30 years typical, 20 years worst case on badly ventilated boxed eaves.
- Maintenance: occasional wash with mild detergent; no painting ever.
- Freeze-thaw: stable across –15°C to +40°C, which comfortably brackets Scottish winter and summer extremes.
- Weakness: can look slightly plasticky on close inspection; expansion joints must be respected on runs over 5 m.
- Do not accept: cap-over installations that leave the original rotten timber fascia in place behind a plastic cover board – the rot continues out of sight and fixings ultimately let go.
Timber
Still required in some conservation areas and on listed buildings where the original was timber, and often specified on high-end period restorations where a factory-finished modern material would look out of place. Species matters: European redwood (Scots pine) with a good factory-applied opaque coating is the working default; western red cedar and accoya offer longer service intervals at a higher price.
Typical 2026 supply-and-fit cost is £45–£80 per linear metre with a factory-primed and top-coated finish, plus ongoing maintenance.
- Lifespan: 15–25 years if maintained on schedule; 8–10 years if neglected.
- Maintenance: repaint or re-treat every 3–5 years – a genuine recurring cost of roughly £15–£25 per linear metre each cycle including access.
- Freeze-thaw: stable if the coating is intact; catastrophic if water penetrates a crack and freezes.
- Where required: Listed buildings and some conservation areas. See our listed building consent guide.
- Where a compromise works: composite gives a similar look without the repainting cycle for most properties that are not formally listed.
Aluminium
Increasingly common on coastal and highly exposed Scottish properties: the Fife coast, the Ayrshire coast, the Aberdeenshire coast and the exposed hill-country properties around the Trossachs, Perthshire and the Angus glens. Coil-coated aluminium to BS EN 1396 does not corrode the way galvanised or steel fixings can, holds its paint finish for decades, and does not soften or sag in prolonged sun exposure the way lower-grade plastics might.
Typical 2026 supply-and-fit cost is £55–£95 per linear metre – roughly 30–50% more than mid-range uPVC.
- Lifespan: 35–40+ years, with the paint finish typically requiring only cleaning across that period.
- Maintenance: minimal; occasional wash to remove salt deposits on coastal properties.
- Freeze-thaw: effectively immune; aluminium's coefficient of thermal expansion is well within the tolerances of the fixing systems used.
- Corrosion: excellent in salt-air environments; see our Fife coastal guide for how coastal exposure changes material choice.
- Best paired with: stainless-steel fixings and, ideally, a matching seamless aluminium gutter system – our seamless aluminium overview covers the whole-roofline case.
Composite (wood-fibre polymer)
A newer option blending wood fibres or sawdust with plastic resins to produce a board that looks closer to real timber than woodgrain uPVC, without the repainting cycle timber demands. Sits between uPVC and timber on cost and looks convincing at ground-level inspection, which is where most people ever look at their own fascia.
Typical 2026 supply-and-fit cost is £40–£65 per linear metre.
- Lifespan: 25–30 years with occasional cleaning.
- Maintenance: occasional wash; no painting; fade over decades but not dramatically.
- Freeze-thaw: stable; less thermal movement than uPVC.
- Best use case: a property that is not listed but where the owner wants a period look and does not want the timber maintenance schedule.
- Watch for: some composite products are effectively uPVC with a printed veneer – ask for a physical sample and check the density.
A direct comparison
| Material | 2026 supply & fit /m | Lifespan | Maintenance | Freeze-thaw | Salt air |
|---|---|---|---|---|---|
| uPVC (BS 7413) | £25–£40 | 25–30 yrs | Clean only | Excellent | Good |
| Timber (redwood) | £45–£80 | 15–25 yrs | Repaint 3–5 yrs | Coating-dependent | Fair (repaint more often) |
| Aluminium (BS EN 1396) | £55–£95 | 35–40+ yrs | Occasional wash | Excellent | Excellent |
| Composite | £40–£65 | 25–30 yrs | Occasional wash | Very good | Very good |
Board thickness and profile
Two boards of the same material can perform very differently. BS 7413 requires uPVC fascia boards to be structurally rated for the fixings and gutter loading they will carry. Cheap 6–7 mm "cap-over" boards designed to be screwed onto an existing timber fascia are not the same product as a 9–16 mm full-replacement board. On a full replacement quote the board thickness and manufacturer should be specified.
Common profiles:
- Square-edge (plain): flat board, simplest to install, most common on post-war Scottish stock.
- Ogee (moulded): decorative curved profile, often on Victorian and Edwardian properties.
- Reveal liner: narrower cap board fitted where the existing timber is being retained.
Which material for your property?
Listed or conservation-area property: check planning first. Timber may be a condition of consent; some conservation areas accept a factory-finished timber-look composite; uPVC is often refused visibly from the street. See our consent guide.
Coastal property: aluminium is worth the premium on any front-line coastal or near-coastal exposure, particularly Fife, East Lothian, Ayrshire and the Angus and Aberdeenshire coasts. Salt air shortens the effective life of poor-quality fixings and finishes far more than most owners expect.
Exposed hill-country or glen property: aluminium or premium uPVC with stainless fixings. Wind-driven rain from the south-west takes down cheap fixings first, not the boards themselves.
Granite property in Aberdeen or the North East: aluminium in a heritage grey often matches the stonework better than a uPVC woodgrain. See our granite roofline guide.
Everything else: quality BS 7413 uPVC remains the sensible default on cost and maintenance alone, and covers the vast majority of Central Scotland domestic properties.
Fixings and installation
The material is only half of the specification. The fixings decide how long the boards actually stay attached. Stainless steel A2 or A4 fixings should be the default in Scotland regardless of board material – plain steel or ordinary galvanised nails rust from the ends and stain the board face within a few winters. Ask what fixings are being used and expect stainless as a minimum on any quote you accept. Our quote red flags guide covers the fixings shortcuts that quietly appear on cheap quotes.
Freeze-thaw behaviour in Scottish winters
Central Scotland averages 40–60 freeze-thaw cycles per winter across a fascia's exposed face, and highland and hill-country properties see 80–120. The cycle count is the number that actually matters for material fatigue – not the annual minimum temperature. A material with excellent thermal cycling behaviour (aluminium, quality composite) will outlast a marginal one (thin cap-over uPVC, poorly coated timber) by a factor of two on the same elevation.
uPVC's linear expansion coefficient of roughly 5–7 × 10⁻⁵/K means a 5 m run of gutter or fascia will move about 3 mm between a January frost and an August sun cap. Expansion joints on runs over 5 m are not optional – they are what stop the board from cracking at the fixings. A quote that does not mention expansion joints on a long run is a quote to check before accepting.
Colour and finish longevity
All modern roofline products are colour-stable across their stated life, but the underlying colour range affects how visible any fading is. White boards do not fade visibly over 25 years. Anthracite grey and rosewood woodgrain finishes hold their colour well on quality products but fade more visibly on cheaper cap boards, particularly on south-facing elevations that see the most UV. On aluminium, the coil coating specification (typically 25—40 micron polyester) determines the fade rate; a premium 60 micron PVDF finish is the specification worth asking about on a high-visibility property.
Frequently asked questions
Which fascia material lasts longest?
Aluminium coil-coated to BS EN 1396 typically lasts 35–40+ years with minimal maintenance, longer than any of the alternatives.
Is uPVC always the cheapest option?
Yes at supply-and-fit stage, but timber's ongoing repainting cost narrows the gap significantly over a 25-year life. Aluminium's lower maintenance and longer life can make it cost-comparable to uPVC over 30 years on an exposed property.
Why choose aluminium over uPVC on a coastal property?
Aluminium resists salt-air corrosion and holds its paint finish far longer than uPVC in prolonged UV, which shortens the fascia replacement cycle on coastal exposures.
Do I have to use timber on a listed property?
Not always – some conservation areas accept factory-finished composite or aluminium in a heritage colour, but a formally listed building will usually require timber matching the original species and profile. Check with the local planning authority first.
What is BS 7413 and why does it matter?
BS 7413 is the British Standard for uPVC fascia and soffit boards, covering material composition, dimensional tolerances, impact resistance and weathering performance. A quote specifying a BS 7413 board is committing to a proper structural fascia rather than a thin cover board.
Not sure which material suits your property?
Get free quotes and material recommendations from local installers.
Get my free quotes →Frequently asked questions
Which fascia material lasts longest?
Aluminium coil-coated to BS EN 1396 typically lasts 35 to 40+ years with minimal maintenance, longer than any of the alternatives.
Is uPVC always the cheapest option?
Yes at supply-and-fit stage, but timber's ongoing repainting cost narrows the gap significantly over a 25-year life. Aluminium can be cost-comparable to uPVC over 30 years on exposed sites.
Why choose aluminium over uPVC on a coastal property?
Aluminium resists salt-air corrosion and holds its paint finish far longer than uPVC in prolonged UV, which shortens the fascia replacement cycle on coastal exposures.
Do I have to use timber on a listed property?
Not always. Some conservation areas accept factory-finished composite or aluminium in a heritage colour, but a formally listed building will usually require timber matching the original.
What is BS 7413 and why does it matter?
BS 7413 is the British Standard for uPVC fascia and soffit boards, covering material composition, dimensional tolerances, impact resistance and weathering performance.